National Standards and Quality Department

The Department's primary mission is to promote Myanmar's trade competitiveness by advancing measurement science, standards, conformity assessment and technology in ways that enhance economic growth and improve our quality of life. The Department will carry out its activities through the development of a National Metrology Institute, National Standards Body and National Accreditation Body.

Comment on a Draft Standard
No. Draft Myanmar Standards Abstract/Scope Committee Closing D- Status Action Review
1 DMMS XXXX:2016 Uniform provisions concerning the approval of motor cycles with regard to noise This Regulation applies to vehicles of category L3 with regard to noise.  Technical Sub-Committee for Auto-mobile Products 23-05-2017 Open Read Comment
2 DMMS XXXX:2016 Uniform provisions concerning the approval of pneumatic tyres for motor cycles and mopeds This Regulation applies to new pneumatic tyres for vehicles of category L1,L2, L3, L4 and L5. However, it does not apply to tyre types designed exclusively for the"off-road" use, which are marked "NHS" (Not for Highway Service) and to tyre types designed exclusively for competitions. Technical Sub-Committee for Auto-mobile Products 23-05-2017 Open Read Comment
3 DMMS ISO 16528-2 : 2007 Boilers and pressure vessels – Part 2: Procedures for fulfilling the requirements of ISO 16528-1 ISO 16528-2:2007 provides a procedure and a standard format for standard-issuing bodies to demonstrate that their standards fulfil the performance requirements of ISO 16528-1. Technical Sub-Committee for Boiler 01-11-2015 Open Read Comment
4 DMMS ISO 16528-1: 2007 Boilers and pressure vessels – Part 1: Performance requirements ISO 16528-1:2007 defines the performance requirements for the construction of boilers and pressure vessels. It is not the intent of ISO 16528-1:2007 to address operation, maintenance and in-service inspection of boilers and pressure vessels. In relation to the geometry of the pressure-containing parts for pressure vessels, ISO 16528-1:2007 includes welding end connection for the first circumferential joint for welded connections, first threaded joint for screwed connections, face of the first flange for bolted, flanged connections, first ... Technical Sub-Committee for Boiler 01-11-2015 Open Read Comment
5 DMMS ISO 8904:1990 Broadleaved sawn timber – Sizes – Methods of measurement Specifies the methods of measurement of the length, width, thickness and volume of sawn timber. Applies to unplaned, square-edged and unedged sawn timber Technical Sub-Committee for Wood Based Product 01-11-2015 Open Read Comment
6 DMMS ISO 8903:1994 Broadleaved sawn timber – Nominal sizes Specifies nominal sizes of unplaned, square-edged and unedged, broadleaved sawn timber. Technical Sub-Committee for Wood Based Product 01-11-2015 Open Read Comment
7 DMMS ISO 8375:2009 Timber structures – Glued laminated timber – Test methods for determination of physical and mechanical properties ISO 8375:2009 specifies test methods for determining the following characteristic values of glued laminated timber: modulus of elasticity in bending; shear modulus; bending strength; modulus of elasticity in tension parallel to the grain; tension strength parallel to the grain; modulus of elasticity in compression parallel to the grain; compression strength parallel to the grain; modulus of elasticity in tension perpendicular to the grain; tension strength perpendicular to the grain; modulus of elasticity in compression perpendicular to the ... Technical Sub-Committee for Wood Based Product 01-11-2015 Open Read Comment
8 DMMS ISO 4471:1981 Wood – Sampling sample trees and logs for determination of physical and mechanical properties of wood in homogeneous stands The method of selecting the appropriate test areas is described. Annexes A to E provide forms for the following: A = Description of the test area and taxation characteristics; B = Overall inventory report on trees growing in the test area No....; C = Inventory report on trees of species to be examined in test area No....; D = Inventory report on selection of sample trees in test area; E = Card of sample tree No.... Technical Sub-Committee for Wood Based Product 01-11-2015 Open Read Comment
9 DMMS ISO 1072:1975 Solid wood parquet – General characteristics Specified are cross-section, dimensions, permissible deviations, etc., the inspection and delivery conditions and the marking of strips with rectangular face of any species of wood. They are manufactured in three different profiles, calles respectively: types P1 (variants A and B), P2 and P3, the dimension characteristics of which are given in tables and shown in figures. Technical Sub-Committee for Wood Based Product 01-11-2015 Open Read Comment
10 DMMS ISO 50001:2011 Energy management systems – Requirements with guidance for use ISO 50001:2011 specifies requirements for establishing, implementing, maintaining and improving an energy management system, whose purpose is to enable an organization to follow a systematic approach in achieving continual improvement of energy performance, including energy efficiency, energy use and consumption. ISO 50001:2011 specifies requirements applicable to energy use and consumption, including measurement, documentation and reporting, design and procurement practices for equipment, systems, processes and personnel that contribute to ... Technical Sub-Committee for Energy 01-11-2015 Open Read Comment
11 DMMS ISO 6410-3:1993 Technical drawings – Screw threads and threaded parts – Part 3: Simplified representation Establishes rules for the simplified representation of threaded parts, with the exception of screw thread inserts, which are covered in ISO 6410-2. This representation is applicable when it is not necessary to show the exact shape and details of the parts (see ISO 6410-1), e.g. in assembly drawings. Technical Sub-Committee for Mechanical 01-11-2015 Open Read Comment
12 DMMS ISO 6410-2:1993 Technical drawings – Screw threads and threaded parts – Part 2: Screw thread inserts Specifies methods for the representation: detailed representation of the true shape, conventional representation, simplified representation, designation and dimensioning. Technical Sub-Committee for Mechanical 01-11-2015 Open Read Comment
13 DMMS ISO 6410-1:1993 Technical drawing – Screw threads and threaded parts – Part 1: General conventions Specifies methods for representation in general: detailed representation, conventional representation, assembled threaded parts, designation and dimensioning, indication of direction of lead. Technical Sub-Committee for Mechanical 01-11-2015 Open Read Comment
14 DMMS/G.652 Series G: Transmission Systems and Media, Digital Systems and Networks Transmission media and optical systems characteristics – Optical fibre cables Describes the geometrical, mechanical, and transmission attributes of a single-mode optical fibre and cable which has zero-dispersion wavelength around 1310 nm. Technical Sub-Committee for Communication and Information Technology 01-11-2015 Open Read Comment
15 DMMS ISO 11852:2012 Rubber -- Determination of magnesium content of field and concentrated natural rubber latex by titration This International Standard specifies titration methods for the determination of the magnesium content of field and concentrated natural rubber latex, respectively. Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
16 DMMS ISO 4660:2011 Rubber, raw natural – Colour index test ISO 4660:2011 specifies a method of determining the colour of raw natural rubber according to a standard colour scale. Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
17 DMMS ISO 2930:2009 Rubber, raw natural – Determination of plasticity retention index (PRI) ISO 2930:2009 specifies a method for determining the plasticity retention index (PRI) of raw natural rubber. The PRI is a measure of the resistance of raw natural rubber to thermal oxidation. A high resistance to thermal oxidation is shown as a high value of the index. Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
18 DMMS ISO 2007:2007 Rubber, unvulcanized – Determination of plasticity – Rapid-plastimeter method ISO 2007:2007 specifies a method for the rapid determination of the plasticity of raw rubber and unvulcanized compounded rubber. It is applicable to the determination of the plasticity retention index (PRI) as specified in ISO 2930, Rubber, raw natural -- Determination of plasticity retention index (PRI). Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
19 DMMS ISO 1802:1992 Natural rubber latex concentrate – Determination of boric acid content Describes the principle, the reagents, the apparatus, the procedure, the expression of results and the contents of the test report. Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
20 DMMS ISO 706:2004 Rubber latex – Determinations of coagulum content (sieve residue) ISO 706:2004 specifies a method for the determination of the coagulum content (sieve residue) of natural rubber latex concentrate and the majority of synthetic rubber latices. It is not suitable for XSBR latices intended for use in paper coating. Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
21 DMMS ISO 506:1992 Rubber latex, natural, concentrate – Determination of volatile fatty acid number The method is not necessarily suitable for latices from natural sources other than Hevea brasiliensis. It is not suitable for compounded latex, vulcanized latex, artificial dispersions of rubber or synthetic rubber latices. Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
22 DMMS ISO 248-1:2011 Rubber, raw – Determination of volatile- matter content – Part 1: Hot-mill method and oven method ISO 248-1:2011 specifies two methods for the determination of volatile-matter content in raw rubbers by using a hot mill or an oven. The methods are applicable to the determination of the volatile-matter content in the "R" group of rubbers listed in ISO 1629. These are rubbers having an unsaturated carbon chain, for example natural rubber and synthetic rubbers derived at least partly from diolefins. The methods can also be applicable to other raw rubbers, but in these cases it is necessary to demonstrate that the change in mass is due solely ... Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
23 DMMS ISO 247:2006 Rubber – Determination of ash ISO 247:2006 specifies two methods for the determination of ash from raw rubbers, compounded rubbers and vulcanizates. The methods are applicable to raw, compounded or vulcanized rubbers of the M, N, O, R and U families described in ISO 1629, except that: Method A is not intended to be used for the determination of ash from compounded or vulcanized rubbers containing chlorine, bromine or iodine. Method B is intended to be used for compounded or vulcanized rubbers containing chlorine, ... Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
24 DMMS ISO 127:2012 Rubber, natural latex concentrate -- Determination of KOH number This International Standard specifies a method for the determination of the KOH number of natural rubber latex concentrate which is preserved wholly or in part with ammonia. The method is applicable to latices containing boric acid. The method is not applicable to latices preserved with potassium hydroxide. It is not necessarily suitable for latices from natural sources other than Hevea brasiliensis, or for latices of synthetic rubber, compounded latex, vulcanized latex or artificial dispersions of rubber. Technical Sub-Committee for Rubber and Rubber-based product 01-11-2015 Open Read Comment
25 DMMS ISO 15747:2010 Plastic containers for intravenous injections ISO 15747:2010 contains requirements that relate to the safe handling and the physical, chemical and biological testing of plastic containers for parenterals. ISO 15747:2010 is applicable to plastic containers for parenterals having one or more chambers and having a total nominal capacity in the range of 50 ml to 5 000 ml such as film bags or blow-moulded plastic bottles for direct administration of infusion (injection) solutions Technical Sub-Committee for Medical devices 01-11-2015 Open Read Comment
26 DMMS XXXX:2015 Myanmar Standard for Rice This standard applies to husked rice, milled rice, and parboiled rice, all for direct human consumption; i.e., ready for its intended use as human food, presented in packaged form or sold loose from the package directly to the consumer. It does not apply to other products derived from rice or to glutinous rice. Technical Sub-Committee for Agro-based Product 01-11-2015 Open Read Comment
27 DMMS ISO 22715:2006 Cosmetics – Packaging and labelling ISO 22715:2006 specifies requirements for packaging and labelling of all cosmetic products as defined according to national regulations or practices intended for sale or free distribution. Technical Sub-Committee for Cosmetics products 01-11-2015 Open Read Comment
28 DMMS XXXX:2015 Uniform provisions concerning the approval of pneumatic tyres for commercial vehicles and their trailers This Regulation covers new pneumatic tyres designed primarily for vehicles of categories M2, M3, N, O3 and O41,2. However, it does not apply to tyre types identified by speed category symbols corresponding to speeds below 80 km/h. Technical Sub-Committee for Auto-mobile Products 01-11-2015 Open Read Comment
29 DMMS XXXX:2015 UNIFORM PROVISIONS CONCERNING THE APPROVAL OF MOTOR CYCLES EQUIPPED WITH A POSITIVE-IGNITION ENGINE WITH REGARD TO THE EMISSION OF GASEOUS POLLUTANTS BY THE ENGINE This Regulation applies to the emission of gaseous pollutants from Positive-ignition engines of two-wheeled or three-wheeled motorcycles with an unladen weight of less than 400 kg having a maximum design speed exceeding 50 km/h and/or cylinder capacity exceeding 50 ccm. Technical Sub-Committee for Auto-mobile Products 01-11-2015 Open Read Comment
30 DMMS XXXX:2015 UNIFORM PROVISIONS CONCERNING THE APPROVAL OF PNEUMATIC TYRES FOR MOTOR VEHICLES AND THEIR TRAILERS This Regulation covers new pneumatic tyres designed primarily, but not only, for vehicles in categories M1, O1 and O2. 1/ It does not apply to tyres designed for (a) the equipment for vintage cars. (b) competitions.   Technical Sub-Committee for Auto-mobile Products 01-11-2015 Open Read Comment